Activity Stream
-
Older Activity
-
13 Minutes AgoCoated the charge pipes Oil lines ran and scavenge pump done Wastegate plumbing done Heat barrier on the floor81 replies | 20885 view(s) -
15 Minutes Ago40949 replies | 929728 view(s) -
21 Minutes Ago40949 replies | 929728 view(s)
-
26 Minutes Ago40949 replies | 929728 view(s)
-
34 Minutes Ago40949 replies | 929728 view(s)
-
35 Minutes AgoHey guys, Been a while, been busy finishing my 91 Z28, 1986 GN and my 78 Bandit, but what the hell I like punishment, so Ive started another project....0 replies | 22 view(s) -
1 Hour Ago40949 replies | 929728 view(s)
-
1 Hour Ago40949 replies | 929728 view(s)
-
1 Hour Ago40949 replies | 929728 view(s)
-
1 Hour Ago40949 replies | 929728 view(s)
-
2 Hours AgoThanks, I was really wondering about whether or not the flex pipe needed extra support at the transmission.5 replies | 106 view(s) -
2 Hours AgoThank you sir! I had thought about running a scavenge pump, I'm a little ways from worrying about it yet but may do that as well to keep the turbo...81 replies | 20885 view(s) -
2 Hours AgoSenek67RS replied to a thread LT4 crate motor Prices - Are there any deals out there? in Open (Pro-Touring) DiscussionWhat kind of prices have you been seeing?1 replies | 49 view(s)
-
2 Hours AgoPiedmont, SC2 replies | 145 view(s)
-
2 Hours Ago40949 replies | 929728 view(s)
-
2 Hours Ago40949 replies | 929728 view(s)
-
2 Hours Ago40949 replies | 929728 view(s)
-
2 Hours Ago40949 replies | 929728 view(s)
-
2 Hours Ago40949 replies | 929728 view(s)
-
2 Hours Ago40949 replies | 929728 view(s)
-
2 Hours Ago40949 replies | 929728 view(s)
-
2 Hours AgoUMI Tech replied to a thread $2500 to spend on suspension. I Don't know where to start. 67 El Camino in SuspensionYes, that exact p/n is for a single though.23 replies | 745 view(s) -
2 Hours Agobrrymnvette replied to a thread $2500 to spend on suspension. I Don't know where to start. 67 El Camino in SuspensionYou talking about this spindle? https://www.speedwaymotors.com/G-Comp-Spindle-GM-AFX-Single,103274.html23 replies | 745 view(s)
-
3 Hours Ago40949 replies | 929728 view(s)
-
3 Hours Ago40949 replies | 929728 view(s)
-
3 Hours AgoThey'll be down at the bottom where water will flow. They may not be an actual "hole". They could be openings along the area where two pieces of the...3 replies | 86 view(s) -
3 Hours Ago40949 replies | 929728 view(s)
-
4 replies | 327 view(s)
-
3 Hours Ago40949 replies | 929728 view(s)
-
3 Hours AgoUMI Tech replied to a thread $2500 to spend on suspension. I Don't know where to start. 67 El Camino in Suspension$2500 The most important front geometry is to get some spindle height whether through tall ball joints or a tall spindle. At UMI we've been using...23 replies | 745 view(s)
