Activity Stream
-
Older Activity
-
2 Hours AgoHi, I like what you done with the mustang. I am follwing your steps it seems as I have a 1969 Mustang and I will drop a 7.3 Godzilla (625hp) with...50 replies | 8335 view(s) -
2 Hours AgoHi, I am following the steps of qnitro.50 replies | 8335 view(s)
-
2 Hours Agochevyz240 replied to a thread another 66 Mustang… again? yes but a bit different. in Project UpdatesThanks!12 replies | 373 view(s) -
11 Hours AgoTire size is a little tricky since it can slightly vary from different manufactures. This is How I figured wheel/tire combo size when i built my...20 replies | 23396 view(s)
-
11 Hours Ago[email protected] replied to a thread Ridetech - 2nd Gen F Body Subframe Connectors now available! in New Products and Product ReviewsThanks! They helped my car a ton. Unfortunately, they won't work with the previous (unicradle) design. I was asking for these a few years ago when I...4 replies | 106 view(s) -
11 Hours Agorobbbc replied to a thread Thinking of switching the coolant temp sensor to passenger rear vs drivers front. in The LSX ForumI run my temp sensor in the passenger side rear of the head. (Ls7 converted to wet sump) No issues with it and don't have a comparison temp but I...1 replies | 56 view(s)
-
12 Hours AgoI have a set of front GM B Body spindles for 12 inch rotors. Also have dust shields and calipers. They were off a mid 80’s full size wagon. I know...0 replies | 59 view(s)
-
12 Hours AgoThanks Mike!15 replies | 991 view(s)
-
12 Hours Agodabuickman started a thread Thinking of switching the coolant temp sensor to passenger rear vs drivers front. in The LSX ForumI have a new LS 3 495hp on order. Should be in a few days. It’s going into my chevelle and I was wondering if there is anyone that has moved their...1 replies | 56 view(s)
-
12 Hours AgoSenek67RS replied to a thread 1969 camaro DSE subframe, DSE Quadra link and more. in For Sale - CarsMan, not sure why these guys are so irritated. A lot of guys aren't able to do metal work, but they can do the assembly. A starting point like this...24 replies | 3558 view(s)
-
13 Hours Agodueling73s replied to a thread Ridetech - 2nd Gen F Body Subframe Connectors now available! in New Products and Product ReviewsOk I jumped too quick and didn't see the link da, yes they fit with composite springs great!4 replies | 106 view(s) -
13 Hours Agodueling73s replied to a thread Ridetech - 2nd Gen F Body Subframe Connectors now available! in New Products and Product ReviewsNice! I assume these will work with your composite leaf springs too??4 replies | 106 view(s)
-
13 Hours AgoAlponcho replied to a thread Ridetech - 2nd Gen F Body Subframe Connectors now available! in New Products and Product ReviewsThese look terrific. Any plans for version that will work with the previous version of your 2nd gen 4 link system (where the lower bar front frame...4 replies | 106 view(s) -
15 Hours AgoThank you, I’m looking forward to building this car up. I’ve been remodeling my house over the last 2 years so I just got her back home.2 replies | 75 view(s) -
15 Hours Agosrode replied to a thread ii much fuel vents, NEVER REPLIES TO EMAILS, NEVER ANSWERS PHONE CALLS in FeedbackAre these P/N 200024 in stock now, for immediate shipping?19 replies | 1322 view(s)
-
15 Hours AgoHey guys, I’m interested and have found a 70 Barracuda Convertible. Looking for opinions on a fair value for myself as well as the owner. The cars...0 replies | 46 view(s)
-
15 Hours AgoHey guys looking for someone near Cheaterfield, VA to check out a 70 Cuda I’m interested in purchasing. Willing to compensate for your time, also...0 replies | 30 view(s)
-
15 Hours Ago68Formula replied to a thread Ridetech Subframe Connectors for 67-69 F body in New Products and Product ReviewsThanks, I do what I can!:) Keep us posted.38 replies | 8693 view(s) -
16 Hours Ago[email protected] started a thread Ridetech - 2nd Gen F Body Subframe Connectors now available! in New Products and Product ReviewsHey everyone! The 2nd gen F-body subframe connectors have made their way through production and are on the shelf now! Just like the 1st gen...4 replies | 106 view(s)
-
16 Hours AgoI built a new hood latch support and mounted it on that. It's about as low as you can get it.6 replies | 557 view(s)
-
16 Hours AgoIt was great at first. But then I got tired of it to be honest. I got rid of it and put a epoxy floor in the new garage. If you dropped a small...45 replies | 7654 view(s)
-
17 Hours Ago[email protected] replied to a thread Ridetech Subframe Connectors for 67-69 F body in New Products and Product ReviewsYou actually got me to laugh out loud with this one, thanks for that! Haha :twothumbs I haven't forgot you! I was picking on the production...38 replies | 8693 view(s)
-
18 Hours AgoStill looking3 replies | 270 view(s) -
19 Hours AgoGreat Project! Good luck with the build!2 replies | 75 view(s)
-
19 Hours AgoThank you.6 replies | 658 view(s) -
19 Hours AgoThank you.6 replies | 658 view(s)
-
20 Hours AgoI think the overseas knockoffs kicked Felser off the market. I don't see them listed anymore on his site. Billet Specialties makes a set. I would say...3 replies | 218 view(s)
-
20 Hours AgoTry this one. I used it on a 68 Camaro and it worked pretty well with an LS1. One tap was usually enough to kick it on. This module doesn't have RFID...2 replies | 98 view(s)
-
1 Day AgoHey y’all, I’m Lou and just joined up. I have a 64 falcon sprint hardtop that I’ve been collecting parts for over a couple years to start my build...2 replies | 75 view(s)
-
1 Day AgoLonnies Performance replied to a thread Transmission cooling lines hard/braided in Automatic TransmissionsLook into stainless braided Teflon lines. They last much longer than rubber & are also thinner in diameter for easier routing.4 replies | 107 view(s)
