Activity Stream
-
Older Activity
-
1 Hour AgoPic for attention Just to be clear, I'm talking 67-69 camaro and 68-74 nova with rear mounted box. Please specify.2 replies | 33 view(s) -
3 Hours AgoWhat do you think about adding a second, same heat exchanger on top and effectively making it a quad pass design? Andrew631 replies | 83505 view(s) -
4 Hours AgoScot, it’s doable, at least it’s been done. Lou’s Change camaro started that thread on Lateral G on pwm fan control. I know you are familiar with...4 replies | 90 view(s) -
4 Hours AgoDid a little rust repair on the B pillar100 replies | 7910 view(s)
-
4 Hours AgoSince I am using the coupe inner structure, I had to fab the back part where the window seals.100 replies | 7910 view(s)
-
4 Hours AgoI made a little progress today. I built the bumper mount.100 replies | 7910 view(s)
-
4 Hours AgoWhich truck?2 replies | 33 view(s) -
5 Hours AgoI'm kindof in the same boat, only with manual transmission. Years ago i bought an LS3 Connect & cruise harness kit. I was under the impression the...4 replies | 90 view(s) -
5 Hours AgoAnyone have photos of Forgelines with minitubs and stick width rear end?10 replies | 333 view(s)
-
5 Hours AgoGood evening, I have a 327 .030 over with trw pistons, stock rods/crank, Edelbrock air gap intake, Holley 650 dp, and old dart/world cast iron...0 replies | 19 view(s)
-
6 Hours AgoWho here has a 1st Gen Camaro/Nova subframe under their truck? Trying to see how the track width worked out and how wide of front wheels and tires...2 replies | 33 view(s)
-
6 Hours AgoDo you have pics of the caliper mount? Looks fantastic18 replies | 2970 view(s)
-
7 Hours AgoThank you for the info and the videos. Very helpful!9 replies | 365 view(s)
-
7 Hours AgoSold6 replies | 283 view(s)
-
8 Hours AgoThanks for your he reply. I believe the the trans controller is independent but not for sure. I know there is a lan connection between the two but...4 replies | 90 view(s)
-
11 Hours AgoI'm interested, DM me contact info2 replies | 79 view(s)
-
11 Hours AgoJust_a_69 replied to a thread 1969 Camaro Anvil rear notch spoiler gloss carbon fiber in For Sale - PartsSold!!1 replies | 133 view(s)
-
11 Hours AgoFew more pics2 replies | 79 view(s)
-
11 Hours AgoFast Efi 1.0 with the updated color screen . Edelbrock Torker 2 intake and Edelbrock fuel rails, MSD, Blaster coil, Distributor with Taylor wires. I...2 replies | 79 view(s)
-
12 Hours AgoOmaha nebraska6 replies | 283 view(s)
-
12 Hours AgoLocation?6 replies | 283 view(s)
-
12 Hours AgoPart # 10004690. Had this fender at my buddys house for a few years and I'll never use it. It's located just outside of Toronto. $9000 replies | 39 view(s)
-
13 Hours AgoI have LS 1 Camaro brakes on my elcamino and the rear emergency brake set up uses a shoe setup that looks exactly like that.106 replies | 13732 view(s)
-
14 Hours AgoNot much to report. Just recieved the holley terminator x max and the transmission. Still waiting for the vintage air. It's suppose to be in early...5 replies | 436 view(s) -
14 Hours Ago2200 shipped6 replies | 283 view(s)
-
15 Hours AgoI know this probably isn’t very helpful at this point, but your situation is the reason I went with a production style E38 and a Speartech harness...4 replies | 90 view(s) -
16 Hours AgoPerfect, thank you! I think this may be another issue associated. The linkage on the trans is upside down, so I think the trans may be in gear as...2 replies | 66 view(s)
-
18 Hours AgoI would think it will not crank in any gear with the neutral safety switch unplugged. You would have to jumper across it. Don2 replies | 66 view(s)
