Activity Stream
-
Older Activity
-
21 Minutes AgoSweet ride!1 replies | 421 view(s) -
53 Minutes AgoAny updates?4 replies | 1419 view(s) -
1 Hour AgoIs there room for these on a 67 Camaro? If so I'm in1 replies | 172 view(s) -
2 Hours AgoGot the lines back on for final.92 replies | 12468 view(s) -
2 Hours AgoSold7 replies | 1394 view(s)
-
2 Hours AgoBlevinator replied to a thread Katech Racing Forged LS3 with Performance Convers of Tx 2800 stall converter in For Sale - PartsSold6 replies | 522 view(s)
-
2 Hours AgoInjector dynamics ID 850 LS3 injectors New in box with all additional clips parts, etc. only taken out of the box for pictures 650 shipped0 replies | 34 view(s)
-
3 Hours AgoHeat exchanger for 67-69 Camaro This one clears the hood latch, which most of them don’t 830+ tax online. 600 shipped. bought this for my car a...0 replies | 51 view(s)
-
6 Hours AgoHi there, My name is Robert. I’m in the process of building an extreme protouring 1969 Camaro. Looking for ideas and may ask questions along the...0 replies | 22 view(s)
-
7 Hours Ago1st gen S10 LS build. Looking for LS conversion tips0 replies | 18 view(s)
-
9 Hours AgoIs there a difference in vibration with those motor mounts?, I know urethane is stiffer3 replies | 144 view(s) -
9 Hours AgoAnymore pics of your setup, and info on wheels? I will be doing the same as you and OP, have mini tub, running stock width 12 bolt.6 replies | 128 view(s)
-
9 Hours AgoBronze is a good way to go, but check the different ones, as mentioned, McMaster Carr is a good source, pay attention to the load ratings, the bigger...3 replies | 220 view(s) -
24 replies | 2316 view(s)
-
12 Hours AgoJust sent you a PM7 replies | 278 view(s)
-
12 Hours AgoDoes the track width and wheel bolt pattern work for your project? As mentioned, any IRS will be an upgrade from all old solid axle setup. As you...3 replies | 325 view(s) -
13 Hours AgoJust cleaned my inbox, let the messages flow like when I drank the water in Mexico7 replies | 278 view(s) -
13 Hours AgoPm me, your inbox is full. Price shipped to 63775?7 replies | 278 view(s)
-
13 Hours AgoIt should be ok assuming you run large enough wire from the battery to the fuses and that you don’t have anything else connected that generates a lot...2 replies | 93 view(s) -
14 Hours AgoBall bearings aren’t the best option since they will barely ever move. They load rating is half when they are static and the load essentially on one...3 replies | 220 view(s)
-
15 Hours AgoLexon replied to a thread 67-8 Camaro & Firebird Single DIN Radio mounting solution in Car Audio & ElectronicsTell me, is such a bar suitable for me to install any secondary radio?32 replies | 21928 view(s) -
18 Hours AgoLong shot but looking to buy a Baer SS4 13" front brake kit for a Heidts SP-110 A, F, X 2" Drop Spindle. Baer lists the kit as PN 4301526.0 replies | 38 view(s)
-
20 Hours AgoMy 3 year project first gen Nova. 146k mile 5.3 with a Summit cam, T56, Speedway GComp front, Church Boys 4 link rear money pit. Goodguys...379 replies | 414373 view(s)
-
22 Hours AgoThanks guys. That gives me some hope that I can do a 11.5 inch wheel with a stock width rear end. Now I just need to decide if I want to tackle the...6 replies | 128 view(s)
-
22 Hours AgoSorry for the extra camera photo. I can’t delete it.2 replies | 93 view(s)
-
22 Hours AgoI have an LS3 running on a Terminator X. The two 12 volt power feeds are currently connected directly to the battery as the Holley instructions...2 replies | 93 view(s)
-
23 Hours AgoYou're down to the fun stuff! Andrew92 replies | 12468 view(s) -
23 Hours AgoSure nice putting together stuff that fits.92 replies | 12468 view(s)
-
1 Day Ago$4004 replies | 469 view(s) -
1 Day AgoI installed some poly mounts recently from Summit and they worked well. I did it when I was replacing the engine. One tip for you if you decide to do...3 replies | 144 view(s)
