2005 Chevy Corvette build & upgrades & Nova parts donater thread

[bonecrrusher]

In this video I install the new external fuel pump for the Corvette.

I needed another fuel pump to provided the additional fuel requirement that the Corvette will need when running E85.

Tools/Parts Used:
Rivet Gun Rivnut Installer: http://amzn.to/2i3Bcqx
Step Bit: http://amzn.to/2i2Q5t0
Push Pin Pliers: http://amzn.to/2jwHcIj
Trim Removal Tool: http://amzn.to/2k9jAhc
Center Punch: http://amzn.to/2zPfq58
Air Drill: http://amzn.to/2i1mVdE
AN Wrench: http://amzn.to/2jv17ri



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

I installed a smaller supercharger pulley and a larger idler pulley on the C6 - in this I go over how to install both.

Parts/Tools used:
Edelbrock Upgraded Tensioner: http://amzn.to/2jm02CM
Edelbrock 3" Pulley: http://amzn.to/2kqNe1v
102.5" Belt: http://amzn.to/2krdtoo



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

Hello everyone!

I took advantage of the warm weather and took care of some maintenance items on the truck - and go over my latest updates.

If you are interested in the video - please watch it below.

Thanks!

[bonecrrusher]

In this video I go over cutting/creating the new fuel lines for the build.

I used -8 PTFE Hose for the fuel system - while this hose is a bit harder to setup - I won't have the gas vapor smell that happens with traditional stainless braided rubber hose - plus E85 won't break down this hose type.



Parts/Tools Used:
Fuel Line Quick Disconnect Tool: http://amzn.to/2z8gOxy
Evil Energy AN Wrench: http://amzn.to/2z84Eog
Air Powered Drill: http://amzn.to/2z8wgtP
Chisel Set: http://amzn.to/2C1bJFS
Pipe Cutter: http://amzn.to/2ASnGyg
NPT Tap: http://amzn.to/2z8u71e
Step Drill Bit: http://amzn.to/2C0cHSJ
PTFE Hose: http://amzn.to/2ASHNws
AN Adapter Fitting: http://amzn.to/2AD1XNS
45* AN Fitting: http://amzn.to/2ymutxk
90* AN Fitting: http://amzn.to/2ASHrWq
180* AN Fitting: http://amzn.to/2ym2yhg
90* AN Fitting to 3/8 NPT: http://amzn.to/2ASmNFV
Russell Fuel Filter: http://amzn.to/2Cc2rb2

Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

I went to Corvettes at Carlisle this year looking for one part.

The part that I was looking for was a ZR1 hood.

A buddy of mine bought one of those hoods and put it on his Vette - and I thought it looked awesome.

So to help with aero and ventillation - I picked up a ZR1 hood and an ACS vented hood insert.



Also the ZR1 hood is made out of Carbon Fiber and is 1/3 the weight of the factory hood - so dropping some weight up front can't hurt either.



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

Its dyno time! How much Horsepower did the Corvette end up making?

Find out in the video!

Car was tuned at PCM of NC - http://www.pcmofnc.com/



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

I installed a Roto-Fab Radiator Cover for my Chevy SS.

If I had a stock SS - this would bolt on with no issue - but since I have an LSA supercharger, and a custom intake - the stock Roto-Fab radiator cover will not fit.

I ordered the bare cover - and notched it for my oil catch can.

I then primed and painted and installed the Roto-Fab Radiator Cover.



Tools/Parts Used:
Roto-Fab Radiator Cover
VHT Engine Primer: http://amzn.to/2D1jmAe
SEM Trim Black: http://amzn.to/2mfZD5v

Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

In this video I update the custom intake for my LSA swapped Chevy SS.

I wanted to get rid of the polished intake pipes - so I started sanding them with 320 grit.

I then primed and painted and installed the painted intake pieces.

Tools/Parts Used:
Roto-Fab Radiator Cover
VHT Engine Primer: http://amzn.to/2D1jmAe
SEM Paint: http://amzn.to/2mGY2pt
VCM Fender Fill Plate http://amzn.to/2gnfVdM
Cowels Trim http://amzn.to/2iH7c6C




Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

In this video - I continue the build by picking up a new Diff for the Corvette.




Thanks everyone for all of your support!


Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

In this video I tear down the Z06 rear differential - and start repairs on it by replacing the broken housing cover/mount.

Tools/Parts Used:
Harbor Freight Press: https://www.youtube.com/watch?v=athkd...
Kent Moore Bearing Tool J42194
Diff Seal - http://amzn.to/2E7jM6u
Diff Passenger Side Cover: 19132920



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

In this video - I assemble and review the Harbor Freight 20 Ton Hydraulic Press.

Overall the install went pretty smoothly - I had to flip around the press I beam - and change the bolts on the bottom of the press since I put them in the wrong spot.

Hopefully these notes will help save you some time when you assemble your press.

Tools Used:
Harbor Freight #32879 20 Ton Press



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

Hello everyone!

Here is the latest upload in my build series.

Check out the video below to find out what's next for the Vette.



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[2ndroundko]

Man I love your youtube channel you put up some solid content with great quality and editing. I think when I finish school this summer I'm going to vlog my truck and my daughters go kart build.

[bonecrrusher]

Thanks 2nd Round - its a lot of work and effort.

Filming/editing/uploading - but I get enjoyment out of it - and its a great way to share projects!

Speaking of updates:

Hello everyone!

Here is the latest video in my build series.

I had an issue with my transmission - and had a change of plans.

Click the video below to find out what the game plan is!



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

Hello everyone!

Continuing my build - I install an East Coast Supercharging Diff and Trans Brace on my C6Z transaxle.

For more details please check out the video below.



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

Hello everyone!

Continuing my build - the Corvette is finally back from the bodyshop!

I had the ZR1 hood painted Lemans Blue and the ACS hood vent painted a semi-gloss black.

For more details please check out the video below.



Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

Continuing my build - I had a lot of wheel hop the last time I went to the drag strip.

In this video - I install a few more aftermarket parts to help eliminate wheel hop on my Corvette.

Tools/Parts used:
Torque Solutions Transmission Mount: http://amzn.to/2C1UCU6
ECS Torque Tube Brace




Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

Another week - another build update!

With all of the braces and upgrades install - it was finally time to install new z06 transmission and diff.

The transmission went into place after some struggle - after I got it lined up - it slid right in.



Tools/Parts Used:
2 Ton Tripod Stand Short HT52008 http://amzn.to/2tpV9Q0
Torin TR4053 http://amzn.to/2shPv2h

Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

In this video I tear apart the stock C6 Navigation head unit - and install a Navtool Backup Camera Integration Kit.

Parts/Tools Used:
NavTool C6 Corvette Kit NAVRGB3.0+CRVT




Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss

[bonecrrusher]

In this video I install a C7 backup camera onto my C6 Corvette.

I install a GM C7 Corvette backup camera on the car - and connect it to the Navtool Backup Kit that I installed in the last video.

Special thanks to ZEEEE 06 for the help on the wiring!

Great Information Links:
C7 Camera Wiring info:
https://www.corvetteforum.com/forums...post1595220847
NavTool info:
https://www.corvetteforum.com/forums...l-on-c6-3.html

Tools/Parts Used:
C7 Backup Camera - 23508179/23306544
Delphi 5 Pin Weather Pack - http://amzn.to/2u9t944
NavTool C6 Corvette Kit NAVRGB3.0+CRVT




Thanks everyone for all of your support!

Follow me on Instagram: https://www.instagram.com/bonecrrusherss
Follow me on Twitter: https://twitter.com/bonecrrusherss
Like me on Facebook: https://www.facebook.com/bonecrrusherss